3D Ivory White Oak Walling
Our 3D Ivory White Oak Walling is one of the first 3D walling options we offered and remains one of our best sellers to this day. This beautiful alabaster wall will remind you of a classic age and thanks to modern construction techniques and solid materials, will withstand the test of time.
Shipping included on all products.
LuxeWall 3D Ivory White Oak Walling is made from 100% real wood and features solid multi-layered construction, a seamless overlapping design, and true hand-stained veneers, finished with a durable polyurethane topcoat. This product is also engineered with a premium, custom-grade uv-sealed solid eucalyptus backer, providing unparalleled stability and rigidity, keeping your walls looking beautiful for years to come. This wall can be installed using construction adhesive or nails.
Planks measure 9.2" wide x 48" long x 1/2" thick.
You can always be sure that we ship nothing but the highest standards of real wood walling.
**This product does not have a self-stick backer and needs to be installed using construction adhesive or brad nails**
HOW MUCH WALLING DO I NEED?
Enter the length and width of your wall to determine how much you need.
We Recommend ____ Square Feet, or ____ Boxes. (Includes 10% waste)
WALLING INSTALLATION INSTRUCTIONS
This is a generic installation guide only. Installation instructions from the product's manufacturer must be followed. Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood plank. Even though our product goes through many inspections before it leaves the mill, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
NECESSARY SUPPLIES
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 1 1/4” - 1 1/2” Finish Nails
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. For self stick products we recommend first wiping down down your wall with Trisodium Phosphate or similar cleaning agent to ensure maximum adhesion. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
PEEL AND STICK INSTALLATION
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before removing the adhesive to ensure proper fit. Use a floor roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
We recommend face nailing the planks throughout the installation as well to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the roller or the rubber mallet to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look
NAIL INSTALLATION
Note - Can be used with self adhesive walling or with any of our tongue & groove flooring products.
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6" from the ends of each plank. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before nailing to ensure proper fit.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Nail down the length of the tongue side of each plank at a 45 degree angle every 8-12”. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Once you’ve finished installing the entire wall, once again go over it and face nail any spots that aren’t securely stuck to the wall and fill the nail holes with a matching wood putty.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Common Questions
Do I need to acclimate LuxeWall?
Yes! Similar to wood flooring, acclimation is the first step you should take before installing LuxeWall. We recommend a time frame of about 48-72 hours.
Can I find your products in stores?
How long will it stay up?
How is shipping handled?
What if I want to remove it?
Is it easy to cut?
Can I apply this to a ceiling?
Commercial/Retail space, will it work?
Do you have issues with the adhesive not sticking?
- The area was not totally clean before hand.
- The area was still damp before LuxeWall was applied
How thick is the product?
Is this wood or wallpaper?
Can I recycle LuxeWall?
Does LuxeWall ship internationally?
How much does it cost to ship?
How many square feet do I need for my project?
Note: We recommend a 10% waste factor in your calculations when ordering. Also, if you have additional areas requiring extra cuts (like windows) than we consider upping the amount to 15%.
Any promotions or coupons?
Where can I get LuxeWall?
What can I LuxeWall?
Do I need to seal it if I use it as a backsplash? And what kind of sealant can I use?
It's not absolutely necessary to seal LuxeWall when it's used as a backsplash. However, it can help if you are worried about excess splashing or humidity.
Will it work in my bathroom or near moisture?
Can I apply it to a fire place or near heat?
Can it be applied to a textured surface?
Can I put it outside? What if I do not use the adhesive?
Can you put this product on a door?
PROMOTIONAL POLICY
The manner, mode and extent of advertising and promotions on luxewall.com are subject to change without specific notice. Availability & pricing may vary by customer location. Other restrictions apply. All offers are limited to stock on hand; no rain checks are available. Offers not valid on prior purchases, or shipping and processing charges. Offers received by mail or email may not be combined with any other sale, promotion, discount, code, coupon and/or offer. Offers can only be redeemed one time per customer, per order, per year and cannot be combined. Void where prohibited, taxed or otherwise restricted. Returns of any portion of the purchase will require customer to pay for shipment to the warehouse. Shipping costs do not count toward order total when redeeming any coupon. Offers only apply to the 48 contiguous United States unless otherwise noted. Luxewall has the right to end or modify any promotion at any time.
<< DOWNLOADABLE PDF >>
WALLING INSTALLATION INSTRUCTIONS
Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood floor. Even though our product
goes through many inspections before it leaves the plant, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 18 gauge 1-1.5" Finishing Nail
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
BEGIN INSTALLATION
For all products with attached adhesive strips, please refer to the 'Self Stick Method' Section below. For all other products including 3D & Tongue and Groove products, please skip to the 'Nail Method' section.
Self Stick Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before removing the adhesive to ensure proper fit, you may need to cut this final piece to complete the row. Use a j-roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Install walling without finishing or brad nails at your own risk. Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend face nailing or blind nailing all planks throughout the installation, to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Nail Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face or blind nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Use an 18 gauge 1 -1.5” brad or finishing nails to secure planks every 12-14”. If installing a tongue and groove product, blind nail at a 45 degree angle through the tongue. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before nailing to ensure proper fit, you may need to cut this final piece to complete the row.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend applying a bead of construction adhesive in a “S” pattern on the back of each plank. Applying adhesive on the back of each plank will ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
























3D Latham White Oak Walling
This 3D Latham White Oak walling is a rugged masterpiece that harkens back to a simpler time of housing construction. Recapture a part of your history with this impressive and solid wall that your guests won’t be able to resist touching.
Shipping included on all products.
LuxeWall 3D Latham White Oak Walling is made from 100% real wood and features solid multi-layered construction, a seamless overlapping design, and true hand-stained veneers, finished with a durable polyurethane topcoat. This product is also engineered with a premium, custom-grade uv-sealed solid eucalyptus backer, providing unparalleled stability and rigidity, keeping your walls looking beautiful for years to come. This wall can be installed using construction adhesive or nails.
Planks measure 9.2" wide x 48" long x 1/2" thick.
You can always be sure that we ship nothing but the highest standards of real wood walling.
**This product does not have a self-stick backer and needs to be installed using construction adhesive or brad nails**
{{ Learn more about our installation methods }}
HOW MUCH WALLING DO I NEED?
Enter the length and width of your wall to determine how much you need.
We Recommend ____ Square Feet, or ____ Boxes. (Includes 10% waste)
WALLING INSTALLATION INSTRUCTIONS
This is a generic installation guide only. Installation instructions from the product's manufacturer must be followed. Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood plank. Even though our product goes through many inspections before it leaves the mill, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
NECESSARY SUPPLIES
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 1 1/4” - 1 1/2” Finish Nails
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. For self stick products we recommend first wiping down down your wall with Trisodium Phosphate or similar cleaning agent to ensure maximum adhesion. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
PEEL AND STICK INSTALLATION
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before removing the adhesive to ensure proper fit. Use a floor roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
We recommend face nailing the planks throughout the installation as well to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the roller or the rubber mallet to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look
NAIL INSTALLATION
Note - Can be used with self adhesive walling or with any of our tongue & groove flooring products.
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6" from the ends of each plank. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before nailing to ensure proper fit.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Nail down the length of the tongue side of each plank at a 45 degree angle every 8-12”. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Once you’ve finished installing the entire wall, once again go over it and face nail any spots that aren’t securely stuck to the wall and fill the nail holes with a matching wood putty.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Common Questions
Do I need to acclimate LuxeWall?
Yes! Similar to wood flooring, acclimation is the first step you should take before installing LuxeWall. We recommend a time frame of about 48-72 hours.
Can I find your products in stores?
How long will it stay up?
How is shipping handled?
What if I want to remove it?
Is it easy to cut?
Can I apply this to a ceiling?
Commercial/Retail space, will it work?
Do you have issues with the adhesive not sticking?
- The area was not totally clean before hand.
- The area was still damp before LuxeWall was applied
How thick is the product?
Is this wood or wallpaper?
Can I recycle LuxeWall?
Does LuxeWall ship internationally?
How much does it cost to ship?
How many square feet do I need for my project?
Note: We recommend a 10% waste factor in your calculations when ordering. Also, if you have additional areas requiring extra cuts (like windows) than we consider upping the amount to 15%.
Any promotions or coupons?
Where can I get LuxeWall?
What can I LuxeWall?
Do I need to seal it if I use it as a backsplash? And what kind of sealant can I use?
It's not absolutely necessary to seal LuxeWall when it's used as a backsplash. However, it can help if you are worried about excess splashing or humidity.
Will it work in my bathroom or near moisture?
Can I apply it to a fire place or near heat?
Can it be applied to a textured surface?
Can I put it outside? What if I do not use the adhesive?
Can you put this product on a door?
PROMOTIONAL POLICY
The manner, mode and extent of advertising and promotions on luxewall.com are subject to change without specific notice. Availability & pricing may vary by customer location. Other restrictions apply. All offers are limited to stock on hand; no rain checks are available. Offers not valid on prior purchases, or shipping and processing charges. Offers received by mail or email may not be combined with any other sale, promotion, discount, code, coupon and/or offer. Offers can only be redeemed one time per customer, per order, per year and cannot be combined. Void where prohibited, taxed or otherwise restricted. Returns of any portion of the purchase will require customer to pay for shipment to the warehouse. Shipping costs do not count toward order total when redeeming any coupon. Offers only apply to the 48 contiguous United States unless otherwise noted. Luxewall has the right to end or modify any promotion at any time.
<< DOWNLOADABLE PDF >>
WALLING INSTALLATION INSTRUCTIONS
Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood floor. Even though our product
goes through many inspections before it leaves the plant, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 18 gauge 1-1.5" Finishing Nail
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
BEGIN INSTALLATION
For all products with attached adhesive strips, please refer to the 'Self Stick Method' Section below. For all other products including 3D & Tongue and Groove products, please skip to the 'Nail Method' section.
Self Stick Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before removing the adhesive to ensure proper fit, you may need to cut this final piece to complete the row. Use a j-roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Install walling without finishing or brad nails at your own risk. Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend face nailing or blind nailing all planks throughout the installation, to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Nail Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face or blind nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Use an 18 gauge 1 -1.5” brad or finishing nails to secure planks every 12-14”. If installing a tongue and groove product, blind nail at a 45 degree angle through the tongue. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before nailing to ensure proper fit, you may need to cut this final piece to complete the row.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend applying a bead of construction adhesive in a “S” pattern on the back of each plank. Applying adhesive on the back of each plank will ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.












3D Natural Acacia Walling
Warning: Not for those with mild tastes!
This 3D Natural Acacia is poetry in practice with every wall coming out different, unique, and creative. Rather it’s your bedroom or living room, leave your mark on the wall with a masterpiece of your own design.
Shipping included on all products.
LuxeWall 3D Natural Acacia Walling is made from 100% real wood and features solid multi-layered construction, a seamless overlapping design, and true hand-stained veneers finished with a durable polyurethane topcoat.
This product is also engineered with a premium, custom-grade UV-sealed solid eucalyptus backer, providing unparalleled stability and rigidity, keeping your walls looking beautiful for years to come. This wall can be installed using construction adhesive or nails.
Planks measure 9.2" wide x 48" long x 1/2" thick.
You can always be sure that we ship nothing but the highest standards of real wood walling.
**This product does not have a self-stick backer and needs to be installed using construction adhesive or brad nails**
{{ Learn more about our installation methods }}
HOW MUCH WALLING DO I NEED?
Enter the length and width of your wall to determine how much you need.
We Recommend ____ Square Feet, or ____ Boxes. (Includes 10% waste)
WALLING INSTALLATION INSTRUCTIONS
This is a generic installation guide only. Installation instructions from the product's manufacturer must be followed. Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood plank. Even though our product goes through many inspections before it leaves the mill, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
NECESSARY SUPPLIES
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 1 1/4” - 1 1/2” Finish Nails
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. For self stick products we recommend first wiping down down your wall with Trisodium Phosphate or similar cleaning agent to ensure maximum adhesion. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
PEEL AND STICK INSTALLATION
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before removing the adhesive to ensure proper fit. Use a floor roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
We recommend face nailing the planks throughout the installation as well to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the roller or the rubber mallet to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look
NAIL INSTALLATION
Note - Can be used with self adhesive walling or with any of our tongue & groove flooring products.
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6" from the ends of each plank. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before nailing to ensure proper fit.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Nail down the length of the tongue side of each plank at a 45 degree angle every 8-12”. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Once you’ve finished installing the entire wall, once again go over it and face nail any spots that aren’t securely stuck to the wall and fill the nail holes with a matching wood putty.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Common Questions
Do I need to acclimate LuxeWall?
Yes! Similar to wood flooring, acclimation is the first step you should take before installing LuxeWall. We recommend a time frame of about 48-72 hours.
Can I find your products in stores?
How long will it stay up?
How is shipping handled?
What if I want to remove it?
Is it easy to cut?
Can I apply this to a ceiling?
Commercial/Retail space, will it work?
Do you have issues with the adhesive not sticking?
- The area was not totally clean before hand.
- The area was still damp before LuxeWall was applied
How thick is the product?
Is this wood or wallpaper?
Can I recycle LuxeWall?
Does LuxeWall ship internationally?
How much does it cost to ship?
How many square feet do I need for my project?
Note: We recommend a 10% waste factor in your calculations when ordering. Also, if you have additional areas requiring extra cuts (like windows) than we consider upping the amount to 15%.
Any promotions or coupons?
Where can I get LuxeWall?
What can I LuxeWall?
Do I need to seal it if I use it as a backsplash? And what kind of sealant can I use?
It's not absolutely necessary to seal LuxeWall when it's used as a backsplash. However, it can help if you are worried about excess splashing or humidity.
Will it work in my bathroom or near moisture?
Can I apply it to a fire place or near heat?
Can it be applied to a textured surface?
Can I put it outside? What if I do not use the adhesive?
Can you put this product on a door?
PROMOTIONAL POLICY
The manner, mode and extent of advertising and promotions on luxewall.com are subject to change without specific notice. Availability & pricing may vary by customer location. Other restrictions apply. All offers are limited to stock on hand; no rain checks are available. Offers not valid on prior purchases, or shipping and processing charges. Offers received by mail or email may not be combined with any other sale, promotion, discount, code, coupon and/or offer. Offers can only be redeemed one time per customer, per order, per year and cannot be combined. Void where prohibited, taxed or otherwise restricted. Returns of any portion of the purchase will require customer to pay for shipment to the warehouse. Shipping costs do not count toward order total when redeeming any coupon. Offers only apply to the 48 contiguous United States unless otherwise noted. Luxewall has the right to end or modify any promotion at any time.
<< DOWNLOADABLE PDF >>
WALLING INSTALLATION INSTRUCTIONS
Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood floor. Even though our product
goes through many inspections before it leaves the plant, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 18 gauge 1-1.5" Finishing Nail
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
BEGIN INSTALLATION
For all products with attached adhesive strips, please refer to the 'Self Stick Method' Section below. For all other products including 3D & Tongue and Groove products, please skip to the 'Nail Method' section.
Self Stick Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before removing the adhesive to ensure proper fit, you may need to cut this final piece to complete the row. Use a j-roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Install walling without finishing or brad nails at your own risk. Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend face nailing or blind nailing all planks throughout the installation, to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Nail Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face or blind nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Use an 18 gauge 1 -1.5” brad or finishing nails to secure planks every 12-14”. If installing a tongue and groove product, blind nail at a 45 degree angle through the tongue. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before nailing to ensure proper fit, you may need to cut this final piece to complete the row.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend applying a bead of construction adhesive in a “S” pattern on the back of each plank. Applying adhesive on the back of each plank will ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.


























3D Natural Herringbone Walnut Walling
Unlike any other, this 3D Natural Walnut comes in a herringbone design to guarantee you a new wall that is anything but normal. Get inspired by adding this shot of creativity to any room in the house. You’ll be happy you did…
Shipping included on all products.
LuxeWall 3D Natural Herringbone Walnut Walling is made from 100% real wood and features solid multi-layered construction, a seamless overlapping design, and true hand-stained veneers, finished with a durable polyurethane topcoat. This product is also engineered with a premium, custom-grade uv-sealed solid eucalyptus backer, providing unparalleled stability and rigidity, keeping your walls looking beautiful for years to come. This wall can be installed using construction adhesive or nails.
Planks measure 9.2" wide x 48" long x 1/2" thick.
You can always be sure that we ship nothing but the highest standards of real wood walling.
**This product does not have a self-stick backer and needs to be installed using construction adhesive or brad nails**
{{ Learn more about our installation methods }}
HOW MUCH WALLING DO I NEED?
Enter the length and width of your wall to determine how much you need.
We Recommend ____ Square Feet, or ____ Boxes. (Includes 10% waste)
WALLING INSTALLATION INSTRUCTIONS
This is a generic installation guide only. Installation instructions from the product's manufacturer must be followed. Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood plank. Even though our product goes through many inspections before it leaves the mill, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
NECESSARY SUPPLIES
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 1 1/4” - 1 1/2” Finish Nails
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. For self stick products we recommend first wiping down down your wall with Trisodium Phosphate or similar cleaning agent to ensure maximum adhesion. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
PEEL AND STICK INSTALLATION
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before removing the adhesive to ensure proper fit. Use a floor roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
We recommend face nailing the planks throughout the installation as well to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the roller or the rubber mallet to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look
NAIL INSTALLATION
Note - Can be used with self adhesive walling or with any of our tongue & groove flooring products.
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6" from the ends of each plank. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before nailing to ensure proper fit.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Nail down the length of the tongue side of each plank at a 45 degree angle every 8-12”. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Once you’ve finished installing the entire wall, once again go over it and face nail any spots that aren’t securely stuck to the wall and fill the nail holes with a matching wood putty.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Common Questions
Do I need to acclimate LuxeWall?
Yes! Similar to wood flooring, acclimation is the first step you should take before installing LuxeWall. We recommend a time frame of about 48-72 hours.
Can I find your products in stores?
How long will it stay up?
How is shipping handled?
What if I want to remove it?
Is it easy to cut?
Can I apply this to a ceiling?
Commercial/Retail space, will it work?
Do you have issues with the adhesive not sticking?
- The area was not totally clean before hand.
- The area was still damp before LuxeWall was applied
How thick is the product?
Is this wood or wallpaper?
Can I recycle LuxeWall?
Does LuxeWall ship internationally?
How much does it cost to ship?
How many square feet do I need for my project?
Note: We recommend a 10% waste factor in your calculations when ordering. Also, if you have additional areas requiring extra cuts (like windows) than we consider upping the amount to 15%.
Any promotions or coupons?
Where can I get LuxeWall?
What can I LuxeWall?
Do I need to seal it if I use it as a backsplash? And what kind of sealant can I use?
It's not absolutely necessary to seal LuxeWall when it's used as a backsplash. However, it can help if you are worried about excess splashing or humidity.
Will it work in my bathroom or near moisture?
Can I apply it to a fire place or near heat?
Can it be applied to a textured surface?
Can I put it outside? What if I do not use the adhesive?
Can you put this product on a door?
PROMOTIONAL POLICY
The manner, mode and extent of advertising and promotions on luxewall.com are subject to change without specific notice. Availability & pricing may vary by customer location. Other restrictions apply. All offers are limited to stock on hand; no rain checks are available. Offers not valid on prior purchases, or shipping and processing charges. Offers received by mail or email may not be combined with any other sale, promotion, discount, code, coupon and/or offer. Offers can only be redeemed one time per customer, per order, per year and cannot be combined. Void where prohibited, taxed or otherwise restricted. Returns of any portion of the purchase will require customer to pay for shipment to the warehouse. Shipping costs do not count toward order total when redeeming any coupon. Offers only apply to the 48 contiguous United States unless otherwise noted. Luxewall has the right to end or modify any promotion at any time.
<< DOWNLOADABLE PDF >>
WALLING INSTALLATION INSTRUCTIONS
Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood floor. Even though our product
goes through many inspections before it leaves the plant, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 18 gauge 1-1.5" Finishing Nail
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
BEGIN INSTALLATION
For all products with attached adhesive strips, please refer to the 'Self Stick Method' Section below. For all other products including 3D & Tongue and Groove products, please skip to the 'Nail Method' section.
Self Stick Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before removing the adhesive to ensure proper fit, you may need to cut this final piece to complete the row. Use a j-roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Install walling without finishing or brad nails at your own risk. Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend face nailing or blind nailing all planks throughout the installation, to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Nail Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face or blind nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Use an 18 gauge 1 -1.5” brad or finishing nails to secure planks every 12-14”. If installing a tongue and groove product, blind nail at a 45 degree angle through the tongue. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before nailing to ensure proper fit, you may need to cut this final piece to complete the row.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend applying a bead of construction adhesive in a “S” pattern on the back of each plank. Applying adhesive on the back of each plank will ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.


















3D Reclaimed Pine Walling
A new take on an old classic - Our 3D Reclaimed Pine offers a rustic touch to any room that is in desperate need of a getaway. The reclaimed wood offers a variant in design and pattern while ensuring an amazing final result. Also, because it’s reclaimed, you can feel great knowing that you’re adding a little history to your home.
Shipping included on all products.
Planks measure 9.2" wide x 48" long x 1/2" thick.
You can always be sure that we ship nothing but the highest standards of real wood walling.
**This product has a self-stick backer and can be installed using construction adhesive, brad nails, or the attached adhesive strips**
HOW MUCH WALLING DO I NEED?
Enter the length and width of your wall to determine how much you need.
We Recommend ____ Square Feet, or ____ Boxes. (Includes 10% waste)
WALLING INSTALLATION INSTRUCTIONS
This is a generic installation guide only. Installation instructions from the product's manufacturer must be followed. Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood plank. Even though our product goes through many inspections before it leaves the mill, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
NECESSARY SUPPLIES
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 1 1/4” - 1 1/2” Finish Nails
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. For self stick products we recommend first wiping down down your wall with Trisodium Phosphate or similar cleaning agent to ensure maximum adhesion. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
PEEL AND STICK INSTALLATION
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before removing the adhesive to ensure proper fit. Use a floor roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
We recommend face nailing the planks throughout the installation as well to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the roller or the rubber mallet to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look
NAIL INSTALLATION
Note - Can be used with self adhesive walling or with any of our tongue & groove flooring products.
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6" from the ends of each plank. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before nailing to ensure proper fit.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Nail down the length of the tongue side of each plank at a 45 degree angle every 8-12”. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Once you’ve finished installing the entire wall, once again go over it and face nail any spots that aren’t securely stuck to the wall and fill the nail holes with a matching wood putty.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Common Questions
Do I need to acclimate LuxeWall?
Yes! Similar to wood flooring, acclimation is the first step you should take before installing LuxeWall. We recommend a time frame of about 48-72 hours.
Can I find your products in stores?
How long will it stay up?
How is shipping handled?
What if I want to remove it?
Is it easy to cut?
Can I apply this to a ceiling?
Commercial/Retail space, will it work?
Do you have issues with the adhesive not sticking?
- The area was not totally clean before hand.
- The area was still damp before LuxeWall was applied
How thick is the product?
Is this wood or wallpaper?
Can I recycle LuxeWall?
Does LuxeWall ship internationally?
How much does it cost to ship?
How many square feet do I need for my project?
Note: We recommend a 10% waste factor in your calculations when ordering. Also, if you have additional areas requiring extra cuts (like windows) than we consider upping the amount to 15%.
Any promotions or coupons?
Where can I get LuxeWall?
What can I LuxeWall?
Do I need to seal it if I use it as a backsplash? And what kind of sealant can I use?
It's not absolutely necessary to seal LuxeWall when it's used as a backsplash. However, it can help if you are worried about excess splashing or humidity.
Will it work in my bathroom or near moisture?
Can I apply it to a fire place or near heat?
Can it be applied to a textured surface?
Can I put it outside? What if I do not use the adhesive?
Can you put this product on a door?
PROMOTIONAL POLICY
The manner, mode and extent of advertising and promotions on luxewall.com are subject to change without specific notice. Availability & pricing may vary by customer location. Other restrictions apply. All offers are limited to stock on hand; no rain checks are available. Offers not valid on prior purchases, or shipping and processing charges. Offers received by mail or email may not be combined with any other sale, promotion, discount, code, coupon and/or offer. Offers can only be redeemed one time per customer, per order, per year and cannot be combined. Void where prohibited, taxed or otherwise restricted. Returns of any portion of the purchase will require customer to pay for shipment to the warehouse. Shipping costs do not count toward order total when redeeming any coupon. Offers only apply to the 48 contiguous United States unless otherwise noted. Luxewall has the right to end or modify any promotion at any time.
<< DOWNLOADABLE PDF >>
WALLING INSTALLATION INSTRUCTIONS
Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood floor. Even though our product
goes through many inspections before it leaves the plant, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 18 gauge 1-1.5" Finishing Nail
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
BEGIN INSTALLATION
For all products with attached adhesive strips, please refer to the 'Self Stick Method' Section below. For all other products including 3D & Tongue and Groove products, please skip to the 'Nail Method' section.
Self Stick Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before removing the adhesive to ensure proper fit, you may need to cut this final piece to complete the row. Use a j-roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Install walling without finishing or brad nails at your own risk. Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend face nailing or blind nailing all planks throughout the installation, to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Nail Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face or blind nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Use an 18 gauge 1 -1.5” brad or finishing nails to secure planks every 12-14”. If installing a tongue and groove product, blind nail at a 45 degree angle through the tongue. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before nailing to ensure proper fit, you may need to cut this final piece to complete the row.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend applying a bead of construction adhesive in a “S” pattern on the back of each plank. Applying adhesive on the back of each plank will ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.




















3D Stacked Natural Walnut Walling
Light and beautiful, our 3D Natural Walnut won’t jump out at you, but that doesn’t mean it won’t command your attention. Put it up in your office or your living room and see how much it will liven up your atmosphere.
Shipping included on all products.
Planks measure 9.2" wide x 48" long x 1/2" thick.
You can always be sure that we ship nothing but the highest standards of real wood walling.
**This product does not have a self-stick backer and needs to be installed using construction adhesive or brad nails**
{{ Learn more about our installation methods }}
HOW MUCH WALLING DO I NEED?
Enter the length and width of your wall to determine how much you need.
We Recommend ____ Square Feet, or ____ Boxes. (Includes 10% waste)
WALLING INSTALLATION INSTRUCTIONS
This is a generic installation guide only. Installation instructions from the product's manufacturer must be followed. Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood plank. Even though our product goes through many inspections before it leaves the mill, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
NECESSARY SUPPLIES
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 1 1/4” - 1 1/2” Finish Nails
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. For self stick products we recommend first wiping down down your wall with Trisodium Phosphate or similar cleaning agent to ensure maximum adhesion. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
PEEL AND STICK INSTALLATION
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before removing the adhesive to ensure proper fit. Use a floor roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
We recommend face nailing the planks throughout the installation as well to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the roller or the rubber mallet to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look
NAIL INSTALLATION
Note - Can be used with self adhesive walling or with any of our tongue & groove flooring products.
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6" from the ends of each plank. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before nailing to ensure proper fit.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Nail down the length of the tongue side of each plank at a 45 degree angle every 8-12”. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Once you’ve finished installing the entire wall, once again go over it and face nail any spots that aren’t securely stuck to the wall and fill the nail holes with a matching wood putty.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Common Questions
Do I need to acclimate LuxeWall?
Yes! Similar to wood flooring, acclimation is the first step you should take before installing LuxeWall. We recommend a time frame of about 48-72 hours.
Can I find your products in stores?
How long will it stay up?
How is shipping handled?
What if I want to remove it?
Is it easy to cut?
Can I apply this to a ceiling?
Commercial/Retail space, will it work?
Do you have issues with the adhesive not sticking?
- The area was not totally clean before hand.
- The area was still damp before LuxeWall was applied
How thick is the product?
Is this wood or wallpaper?
Can I recycle LuxeWall?
Does LuxeWall ship internationally?
How much does it cost to ship?
How many square feet do I need for my project?
Note: We recommend a 10% waste factor in your calculations when ordering. Also, if you have additional areas requiring extra cuts (like windows) than we consider upping the amount to 15%.
Any promotions or coupons?
Where can I get LuxeWall?
What can I LuxeWall?
Do I need to seal it if I use it as a backsplash? And what kind of sealant can I use?
It's not absolutely necessary to seal LuxeWall when it's used as a backsplash. However, it can help if you are worried about excess splashing or humidity.
Will it work in my bathroom or near moisture?
Can I apply it to a fire place or near heat?
Can it be applied to a textured surface?
Can I put it outside? What if I do not use the adhesive?
Can you put this product on a door?
PROMOTIONAL POLICY
The manner, mode and extent of advertising and promotions on luxewall.com are subject to change without specific notice. Availability & pricing may vary by customer location. Other restrictions apply. All offers are limited to stock on hand; no rain checks are available. Offers not valid on prior purchases, or shipping and processing charges. Offers received by mail or email may not be combined with any other sale, promotion, discount, code, coupon and/or offer. Offers can only be redeemed one time per customer, per order, per year and cannot be combined. Void where prohibited, taxed or otherwise restricted. Returns of any portion of the purchase will require customer to pay for shipment to the warehouse. Shipping costs do not count toward order total when redeeming any coupon. Offers only apply to the 48 contiguous United States unless otherwise noted. Luxewall has the right to end or modify any promotion at any time.
<< DOWNLOADABLE PDF >>
WALLING INSTALLATION INSTRUCTIONS
Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood floor. Even though our product
goes through many inspections before it leaves the plant, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 18 gauge 1-1.5" Finishing Nail
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
BEGIN INSTALLATION
For all products with attached adhesive strips, please refer to the 'Self Stick Method' Section below. For all other products including 3D & Tongue and Groove products, please skip to the 'Nail Method' section.
Self Stick Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before removing the adhesive to ensure proper fit, you may need to cut this final piece to complete the row. Use a j-roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Install walling without finishing or brad nails at your own risk. Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend face nailing or blind nailing all planks throughout the installation, to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Nail Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face or blind nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Use an 18 gauge 1 -1.5” brad or finishing nails to secure planks every 12-14”. If installing a tongue and groove product, blind nail at a 45 degree angle through the tongue. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before nailing to ensure proper fit, you may need to cut this final piece to complete the row.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend applying a bead of construction adhesive in a “S” pattern on the back of each plank. Applying adhesive on the back of each plank will ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.










Loano White Oak Walling
If we had a walling hall of fame, then our Loano White Oak would the first inducted. It is our quintessential bestseller and after just one look at the pictures, you can tell why. Robust and flexible, it is perfect for any room.
Shipping included on all walls.
LuxeWall Loano White Oak Walling is made from 100% real wood and features solid one-piece construction, a square-edge design, and true hand-stained veneers, finished with a durable matte oil topcoat. This wall can be installed using the provided adhesive strips, construction adhesive, or nails.
Planks measure 5" wide x up to 48" long x 7mm thick.
You can always be sure that we ship nothing but the highest standards of real wood walling.
**This product has a self-stick backer and can be installed using construction adhesive, brad nails, or the attached adhesive strips**
{{ Learn more about our installation methods }}
HOW MUCH WALLING DO I NEED?
Enter the length and width of your wall to determine how much you need.
We Recommend ____ Square Feet, or ____ Boxes. (Includes 10% waste)
WALLING INSTALLATION INSTRUCTIONS
This is a generic installation guide only. Installation instructions from the product's manufacturer must be followed. Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood plank. Even though our product goes through many inspections before it leaves the mill, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
NECESSARY SUPPLIES
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 1 1/4” - 1 1/2” Finish Nails
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. For self stick products we recommend first wiping down down your wall with Trisodium Phosphate or similar cleaning agent to ensure maximum adhesion. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
PEEL AND STICK INSTALLATION
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before removing the adhesive to ensure proper fit. Use a floor roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
We recommend face nailing the planks throughout the installation as well to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the roller or the rubber mallet to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look
NAIL INSTALLATION
Note - Can be used with self adhesive walling or with any of our tongue & groove flooring products.
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6" from the ends of each plank. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before nailing to ensure proper fit.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Nail down the length of the tongue side of each plank at a 45 degree angle every 8-12”. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Once you’ve finished installing the entire wall, once again go over it and face nail any spots that aren’t securely stuck to the wall and fill the nail holes with a matching wood putty.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Common Questions
Do I need to acclimate LuxeWall?
Yes! Similar to wood flooring, acclimation is the first step you should take before installing LuxeWall. We recommend a time frame of about 48-72 hours.
Can I find your products in stores?
How long will it stay up?
How is shipping handled?
What if I want to remove it?
Is it easy to cut?
Can I apply this to a ceiling?
Commercial/Retail space, will it work?
Do you have issues with the adhesive not sticking?
- The area was not totally clean before hand.
- The area was still damp before LuxeWall was applied
How thick is the product?
Is this wood or wallpaper?
Can I recycle LuxeWall?
Does LuxeWall ship internationally?
How much does it cost to ship?
How many square feet do I need for my project?
Note: We recommend a 10% waste factor in your calculations when ordering. Also, if you have additional areas requiring extra cuts (like windows) than we consider upping the amount to 15%.
Any promotions or coupons?
Where can I get LuxeWall?
What can I LuxeWall?
Do I need to seal it if I use it as a backsplash? And what kind of sealant can I use?
It's not absolutely necessary to seal LuxeWall when it's used as a backsplash. However, it can help if you are worried about excess splashing or humidity.
Will it work in my bathroom or near moisture?
Can I apply it to a fire place or near heat?
Can it be applied to a textured surface?
Can I put it outside? What if I do not use the adhesive?
Can you put this product on a door?
PROMOTIONAL POLICY
The manner, mode and extent of advertising and promotions on luxewall.com are subject to change without specific notice. Availability & pricing may vary by customer location. Other restrictions apply. All offers are limited to stock on hand; no rain checks are available. Offers not valid on prior purchases, or shipping and processing charges. Offers received by mail or email may not be combined with any other sale, promotion, discount, code, coupon and/or offer. Offers can only be redeemed one time per customer, per order, per year and cannot be combined. Void where prohibited, taxed or otherwise restricted. Returns of any portion of the purchase will require customer to pay for shipment to the warehouse. Shipping costs do not count toward order total when redeeming any coupon. Offers only apply to the 48 contiguous United States unless otherwise noted. Luxewall has the right to end or modify any promotion at any time.
<< DOWNLOADABLE PDF >>
WALLING INSTALLATION INSTRUCTIONS
Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood floor. Even though our product
goes through many inspections before it leaves the plant, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 18 gauge 1-1.5" Finishing Nail
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
BEGIN INSTALLATION
For all products with attached adhesive strips, please refer to the 'Self Stick Method' Section below. For all other products including 3D & Tongue and Groove products, please skip to the 'Nail Method' section.
Self Stick Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before removing the adhesive to ensure proper fit, you may need to cut this final piece to complete the row. Use a j-roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Install walling without finishing or brad nails at your own risk. Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend face nailing or blind nailing all planks throughout the installation, to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Nail Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face or blind nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Use an 18 gauge 1 -1.5” brad or finishing nails to secure planks every 12-14”. If installing a tongue and groove product, blind nail at a 45 degree angle through the tongue. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before nailing to ensure proper fit, you may need to cut this final piece to complete the row.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend applying a bead of construction adhesive in a “S” pattern on the back of each plank. Applying adhesive on the back of each plank will ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.














Natural Acacia Walling
This Natural Acacia walling just might be our all-time best seller… and for good reasons. This wall is poetry in practice with every wall coming out different, unique, and creative. Rather it’s your bedroom or living room, leave your mark on the wall with a masterpiece of your own design.
Shipping included on all products.
Planks measure 5" wide x up to 48" long x 7mm thick.
You can always be sure that we ship nothing but the highest standards of real wood walling.
**This product has a self-stick backer and can be installed using construction adhesive, brad nails, or the attached adhesive strips**
{{ Learn more about our installation methods }}
HOW MUCH WALLING DO I NEED?
Enter the length and width of your wall to determine how much you need.
We Recommend ____ Square Feet, or ____ Boxes. (Includes 10% waste)
WALLING INSTALLATION INSTRUCTIONS
This is a generic installation guide only. Installation instructions from the product's manufacturer must be followed. Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood plank. Even though our product goes through many inspections before it leaves the mill, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
NECESSARY SUPPLIES
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 1 1/4” - 1 1/2” Finish Nails
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. For self stick products we recommend first wiping down down your wall with Trisodium Phosphate or similar cleaning agent to ensure maximum adhesion. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
PEEL AND STICK INSTALLATION
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before removing the adhesive to ensure proper fit. Use a floor roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
We recommend face nailing the planks throughout the installation as well to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the roller or the rubber mallet to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look
NAIL INSTALLATION
Note - Can be used with self adhesive walling or with any of our tongue & groove flooring products.
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6" from the ends of each plank. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before nailing to ensure proper fit.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Nail down the length of the tongue side of each plank at a 45 degree angle every 8-12”. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Once you’ve finished installing the entire wall, once again go over it and face nail any spots that aren’t securely stuck to the wall and fill the nail holes with a matching wood putty.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Common Questions
Do I need to acclimate LuxeWall?
Yes! Similar to wood flooring, acclimation is the first step you should take before installing LuxeWall. We recommend a time frame of about 48-72 hours.
Can I find your products in stores?
How long will it stay up?
How is shipping handled?
What if I want to remove it?
Is it easy to cut?
Can I apply this to a ceiling?
Commercial/Retail space, will it work?
Do you have issues with the adhesive not sticking?
- The area was not totally clean before hand.
- The area was still damp before LuxeWall was applied
How thick is the product?
Is this wood or wallpaper?
Can I recycle LuxeWall?
Does LuxeWall ship internationally?
How much does it cost to ship?
How many square feet do I need for my project?
Note: We recommend a 10% waste factor in your calculations when ordering. Also, if you have additional areas requiring extra cuts (like windows) than we consider upping the amount to 15%.
Any promotions or coupons?
Where can I get LuxeWall?
What can I LuxeWall?
Do I need to seal it if I use it as a backsplash? And what kind of sealant can I use?
It's not absolutely necessary to seal LuxeWall when it's used as a backsplash. However, it can help if you are worried about excess splashing or humidity.
Will it work in my bathroom or near moisture?
Can I apply it to a fire place or near heat?
Can it be applied to a textured surface?
Can I put it outside? What if I do not use the adhesive?
Can you put this product on a door?
PROMOTIONAL POLICY
The manner, mode and extent of advertising and promotions on luxewall.com are subject to change without specific notice. Availability & pricing may vary by customer location. Other restrictions apply. All offers are limited to stock on hand; no rain checks are available. Offers not valid on prior purchases, or shipping and processing charges. Offers received by mail or email may not be combined with any other sale, promotion, discount, code, coupon and/or offer. Offers can only be redeemed one time per customer, per order, per year and cannot be combined. Void where prohibited, taxed or otherwise restricted. Returns of any portion of the purchase will require customer to pay for shipment to the warehouse. Shipping costs do not count toward order total when redeeming any coupon. Offers only apply to the 48 contiguous United States unless otherwise noted. Luxewall has the right to end or modify any promotion at any time.
<< DOWNLOADABLE PDF >>
WALLING INSTALLATION INSTRUCTIONS
Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood floor. Even though our product
goes through many inspections before it leaves the plant, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 18 gauge 1-1.5" Finishing Nail
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
BEGIN INSTALLATION
For all products with attached adhesive strips, please refer to the 'Self Stick Method' Section below. For all other products including 3D & Tongue and Groove products, please skip to the 'Nail Method' section.
Self Stick Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before removing the adhesive to ensure proper fit, you may need to cut this final piece to complete the row. Use a j-roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Install walling without finishing or brad nails at your own risk. Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend face nailing or blind nailing all planks throughout the installation, to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Nail Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face or blind nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Use an 18 gauge 1 -1.5” brad or finishing nails to secure planks every 12-14”. If installing a tongue and groove product, blind nail at a 45 degree angle through the tongue. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before nailing to ensure proper fit, you may need to cut this final piece to complete the row.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend applying a bead of construction adhesive in a “S” pattern on the back of each plank. Applying adhesive on the back of each plank will ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.


















Reclaimed Rustic Pine Walling
Add a rustic touch to any room that is in desperate need of a getaway. The reclaimed wood offers a variant in design and pattern while ensuring an amazing final result. Also, because it’s reclaimed, you can feel great knowing that you’re adding a little history to your home.
Shipping included on all walls.
Planks measure up to 4.5" wide x up to 40" long x 3/8" thick.
You can always be sure that we ship nothing but the highest standards of real wood walling.
**This product has a self-stick backer and can be installed using construction adhesive, brad nails, or the attached adhesive strips**
{{ Learn more about our installation methods }}
HOW MUCH WALLING DO I NEED?
Enter the length and width of your wall to determine how much you need.
We Recommend ____ Square Feet, or ____ Boxes. (Includes 10% waste)
WALLING INSTALLATION INSTRUCTIONS
This is a generic installation guide only. Installation instructions from the product's manufacturer must be followed. Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood plank. Even though our product goes through many inspections before it leaves the mill, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
NECESSARY SUPPLIES
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 1 1/4” - 1 1/2” Finish Nails
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. For self stick products we recommend first wiping down down your wall with Trisodium Phosphate or similar cleaning agent to ensure maximum adhesion. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
PEEL AND STICK INSTALLATION
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before removing the adhesive to ensure proper fit. Use a floor roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
We recommend face nailing the planks throughout the installation as well to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the roller or the rubber mallet to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look
NAIL INSTALLATION
Note - Can be used with self adhesive walling or with any of our tongue & groove flooring products.
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6" from the ends of each plank. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before nailing to ensure proper fit.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Nail down the length of the tongue side of each plank at a 45 degree angle every 8-12”. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Once you’ve finished installing the entire wall, once again go over it and face nail any spots that aren’t securely stuck to the wall and fill the nail holes with a matching wood putty.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Common Questions
Do I need to acclimate LuxeWall?
Yes! Similar to wood flooring, acclimation is the first step you should take before installing LuxeWall. We recommend a time frame of about 48-72 hours.
Can I find your products in stores?
How long will it stay up?
How is shipping handled?
What if I want to remove it?
Is it easy to cut?
Can I apply this to a ceiling?
Commercial/Retail space, will it work?
Do you have issues with the adhesive not sticking?
- The area was not totally clean before hand.
- The area was still damp before LuxeWall was applied
How thick is the product?
Is this wood or wallpaper?
Can I recycle LuxeWall?
Does LuxeWall ship internationally?
How much does it cost to ship?
How many square feet do I need for my project?
Note: We recommend a 10% waste factor in your calculations when ordering. Also, if you have additional areas requiring extra cuts (like windows) than we consider upping the amount to 15%.
Any promotions or coupons?
Where can I get LuxeWall?
What can I LuxeWall?
Do I need to seal it if I use it as a backsplash? And what kind of sealant can I use?
It's not absolutely necessary to seal LuxeWall when it's used as a backsplash. However, it can help if you are worried about excess splashing or humidity.
Will it work in my bathroom or near moisture?
Can I apply it to a fire place or near heat?
Can it be applied to a textured surface?
Can I put it outside? What if I do not use the adhesive?
Can you put this product on a door?
PROMOTIONAL POLICY
The manner, mode and extent of advertising and promotions on luxewall.com are subject to change without specific notice. Availability & pricing may vary by customer location. Other restrictions apply. All offers are limited to stock on hand; no rain checks are available. Offers not valid on prior purchases, or shipping and processing charges. Offers received by mail or email may not be combined with any other sale, promotion, discount, code, coupon and/or offer. Offers can only be redeemed one time per customer, per order, per year and cannot be combined. Void where prohibited, taxed or otherwise restricted. Returns of any portion of the purchase will require customer to pay for shipment to the warehouse. Shipping costs do not count toward order total when redeeming any coupon. Offers only apply to the 48 contiguous United States unless otherwise noted. Luxewall has the right to end or modify any promotion at any time.
<< DOWNLOADABLE PDF >>
WALLING INSTALLATION INSTRUCTIONS
Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood floor. Even though our product
goes through many inspections before it leaves the plant, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 18 gauge 1-1.5" Finishing Nail
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
BEGIN INSTALLATION
For all products with attached adhesive strips, please refer to the 'Self Stick Method' Section below. For all other products including 3D & Tongue and Groove products, please skip to the 'Nail Method' section.
Self Stick Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before removing the adhesive to ensure proper fit, you may need to cut this final piece to complete the row. Use a j-roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Install walling without finishing or brad nails at your own risk. Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend face nailing or blind nailing all planks throughout the installation, to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Nail Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face or blind nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Use an 18 gauge 1 -1.5” brad or finishing nails to secure planks every 12-14”. If installing a tongue and groove product, blind nail at a 45 degree angle through the tongue. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before nailing to ensure proper fit, you may need to cut this final piece to complete the row.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend applying a bead of construction adhesive in a “S” pattern on the back of each plank. Applying adhesive on the back of each plank will ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.












































Smooth Natural Walnut Walling
Our Natural Walnut is a modern take on a classic. Bring out the elegance and beauty of any space with ease. Robust and flexible, it really is perfect for any room.
Shipping included on all walls.
LuxeWall Walling is made from 100% real wood and features solid one-piece construction, a square-edge design, and true hand-stained veneers, finished with a durable matte oil topcoat. This wall can be installed using the provided adhesive strips, construction adhesive, or nails.
HOW MUCH WALLING DO I NEED?
Enter the length and width of your wall to determine how much you need.
We Recommend ____ Square Feet, or ____ Boxes. (Includes 10% waste)
Planks measure 5" wide x up to 48" long x 7mm thick.
You can always be sure that we ship nothing but the highest standards of real wood walling.
**This product has a self-stick backer and can be installed using construction adhesive, brad nails, or the attached adhesive strips**
WALLING INSTALLATION INSTRUCTIONS
This is a generic installation guide only. Installation instructions from the product's manufacturer must be followed. Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood plank. Even though our product goes through many inspections before it leaves the mill, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
NECESSARY SUPPLIES
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 1 1/4” - 1 1/2” Finish Nails
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. For self stick products we recommend first wiping down down your wall with Trisodium Phosphate or similar cleaning agent to ensure maximum adhesion. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
PEEL AND STICK INSTALLATION
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before removing the adhesive to ensure proper fit. Use a floor roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
We recommend face nailing the planks throughout the installation as well to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the roller or the rubber mallet to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look
NAIL INSTALLATION
Note - Can be used with self adhesive walling or with any of our tongue & groove flooring products.
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6" from the ends of each plank. Continue installing the planks across the wall until you reach the other side and cut the last plank to fit against the wall. Test fit the last plank before nailing to ensure proper fit.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Nail down the length of the tongue side of each plank at a 45 degree angle every 8-12”. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Once you’ve finished installing the entire wall, once again go over it and face nail any spots that aren’t securely stuck to the wall and fill the nail holes with a matching wood putty.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Common Questions
Do I need to acclimate LuxeWall?
Yes! Similar to wood flooring, acclimation is the first step you should take before installing LuxeWall. We recommend a time frame of about 48-72 hours.
Can I find your products in stores?
How long will it stay up?
How is shipping handled?
What if I want to remove it?
Is it easy to cut?
Can I apply this to a ceiling?
Commercial/Retail space, will it work?
Do you have issues with the adhesive not sticking?
- The area was not totally clean before hand.
- The area was still damp before LuxeWall was applied
How thick is the product?
Is this wood or wallpaper?
Can I recycle LuxeWall?
Does LuxeWall ship internationally?
How much does it cost to ship?
How many square feet do I need for my project?
Note: We recommend a 10% waste factor in your calculations when ordering. Also, if you have additional areas requiring extra cuts (like windows) than we consider upping the amount to 15%.
Any promotions or coupons?
Where can I get LuxeWall?
What can I LuxeWall?
Do I need to seal it if I use it as a backsplash? And what kind of sealant can I use?
It's not absolutely necessary to seal LuxeWall when it's used as a backsplash. However, it can help if you are worried about excess splashing or humidity.
Will it work in my bathroom or near moisture?
Can I apply it to a fire place or near heat?
Can it be applied to a textured surface?
Can I put it outside? What if I do not use the adhesive?
Can you put this product on a door?
PROMOTIONAL POLICY
The manner, mode and extent of advertising and promotions on luxewall.com are subject to change without specific notice. Availability & pricing may vary by customer location. Other restrictions apply. All offers are limited to stock on hand; no rain checks are available. Offers not valid on prior purchases, or shipping and processing charges. Offers received by mail or email may not be combined with any other sale, promotion, discount, code, coupon and/or offer. Offers can only be redeemed one time per customer, per order, per year and cannot be combined. Void where prohibited, taxed or otherwise restricted. Returns of any portion of the purchase will require customer to pay for shipment to the warehouse. Shipping costs do not count toward order total when redeeming any coupon. Offers only apply to the 48 contiguous United States unless otherwise noted. Luxewall has the right to end or modify any promotion at any time.
<< DOWNLOADABLE PDF >>
WALLING INSTALLATION INSTRUCTIONS
Inspect ALL materials carefully BEFORE installation. Wood is a natural product containing characteristics such as variations in color, tone and wood grain. Some variation in color is to be expected in a natural wood floor. Even though our product
goes through many inspections before it leaves the plant, it is the customer and installer’s responsibility to do the final inspection prior to installation. Warranties DO NOT cover materials with visible defects once they are installed.
- Level
- Pencil
- Tape Measure
- Saw
- Finish Nailer
- 18 gauge 1-1.5" Finishing Nail
- Rubber Mallet
- Floor Roller
PREPARE YOUR SURFACE
Your new walling is designed to stick to a wide variety of surfaces. The surface you’re applying to must be flat, dry, and structurally sound. If the surface has been recently painted, you must wait 24-48 hours to ensure that it’s fully cured if you plan to use the self stick backing. You must allow the walling to acclimate for 48 hours prior to installation and it should not be installed at a temperature less than 60 degrees. For best results, humidity levels of 35-55% must be maintained after installation. If these rules are not followed, you will likely not get a secure bond between your new walling and the surface you are installing over.
- Remove any electrical plates and light switch covers.
- Scrape off any debris or loose pieces of wallpaper/drywall/etc.
- Remove any nails, staples, or anything else that may cause the walling not to stick to the wall.
- Wipe your surface clean to ensure a solid bond.
- Before you begin installing, be sure to lay out planks from several boxes to make sure that you have a good variety of different shade planks and lengths to achieve a random look.
BEGIN INSTALLATION
For all products with attached adhesive strips, please refer to the 'Self Stick Method' Section below. For all other products including 3D & Tongue and Groove products, please skip to the 'Nail Method' section.
Self Stick Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
Remove the adhesive backing and attach your first board to the wall, ensuring that you keep it even with the line. For the first row, face nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before removing the adhesive to ensure proper fit, you may need to cut this final piece to complete the row. Use a j-roller or a rubber mallet along the entire row to ensure the adhesive is stuck firmly to the entire wall.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Install walling without finishing or brad nails at your own risk. Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend face nailing or blind nailing all planks throughout the installation, to ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.
Nail Method
Using a level and a pencil, mark a straight line across the wall to start your first row off of.
For the first row, face or blind nail each plank in several spots ensuring that you keep it even with the line that you just marked. We recommend nailing no closer than 6” from the ends of each plank. Use an 18 gauge 1 -1.5” brad or finishing nails to secure planks every 12-14”. If installing a tongue and groove product, blind nail at a 45 degree angle through the tongue. Continue installing the planks across the wall, making sure each plank is level and lined up with the other planks on the row. Test fit the last plank before nailing to ensure proper fit, you may need to cut this final piece to complete the row.
Begin installing the next row using the cut piece left from the previous row while ensuring the end gaps from one row to another are staggered by at least 6” to create a random, natural look. Repeat that process until you reach the ceiling. On the last row, cut the planks lengthwise to fit while leaving a 3/8” expansion gap against the ceiling. This is critical, as wood is a natural product that expands and contracts.
Repeat below the first row you installed until you reach the floor.
Because each job site is unique unto itself, and due to differences in climate, humidity, existing wall finishes and gloss levels, we recommend applying a bead of construction adhesive in a “S” pattern on the back of each plank. Applying adhesive on the back of each plank will ensure a secure hold for years to come.
Once you’ve finished installing the entire wall, once again go over it with the j-roller (3D or square edge products) or the rubber mallet (Tongue & Groove Products) to ensure that the self adhesive has a solid bond to the wall.
If any gaps are left around the perimeter, quarter round can be used to create a clean finished look.





